Grand Canyon Water Heaters
Desert landscape with saguaro cacti and low shrubs on a rocky slope, with distant mountain ranges under a clear blue sky.Get matched

Gas or electric water heater for an Arizona home

Get in touch with a local installer about a new water heater.

Most homes in Arizona heat with electricity, and that includes the water heater. If yours runs on electric, switching to gas means running a gas line to the tank, and that's a different job than swapping one electric tank for another. If you already have gas, the question is simpler, but it still comes down to what your house is set up for and what you want it to do.

Electric water heaters cost more to run here than gas ones do, because gas is the cheaper way to heat water in most homes. But the installation itself is more involved if you're switching fuels. Someone needs to look at where your gas line runs, whether it reaches the water heater's location, and what venting a gas tank would need that an electric one never did.

That's a judgment call that depends on your house, not a general rule about Arizona. A contractor who installs water heaters in this area regularly has seen both setups often enough to tell you quickly whether a switch is worth the work, or whether staying electric and picking the right size and recovery rate is the better move for your home.

This page connects you with one licensed contractor local to your area, not a handful competing for your call. That matters here because water heater installation in Arizona often comes down to specifics: gas line access, venting, the heat and dryness that affect where a tank can go. A local contractor has installed water heaters in homes like yours before and knows what questions to ask before giving you an answer.

Tell the page a little about your situation, and that contractor will reach out to go over what your home actually needs.

Most Arizona homes do fine with an electric water heater, and since power here runs at a typical price, there's no cost penalty for staying electric. Gas heats water faster and recovers quicker after a long shower or a full tub, which matters more to some households than others. The real question is usually what you already have. An electric tank can be swapped for another electric tank without touching your home's gas lines or venting. Switching from electric to gas means running a new gas line and adding venting for the exhaust, which makes it a bigger job with more that has to be done correctly. If your home already has a gas line to the water heater, staying with gas keeps the installation simple. If it doesn't, adding one is possible but it's worth knowing that going in, since it changes what the installation involves and who needs to do it.

A light gray cylindrical water heater with two access panels stands on a concrete floor against a concrete wall, with copper and black pipes beside it and an unfinished wood stud wall to the right.
An electric tank like this one ties into your home's wiring and the supply lines already in place, with nothing new to route.
An older white gas water heater with rust staining and an exposed vertical pipe stands against a concrete block basement wall, with a metal flue above and black vertical pipes to the right.
A gas tank in this condition, or one you're adding gas service for, needs a vent and gas line a local licensed installer has to get right.

How Each Type Actually Heats

  • An electric tank uses one or two heating elements submerged in the water, and the thermostat switches them on as the tank cools.
  • A gas tank heats water with a burner under the tank, and the flue runs straight up through the center to vent exhaust outside.
  • Gas models need a draft hood or power vent so the flue gases clear the house, which electric tanks don't need at all.
  • A gas installer has to size the gas line correctly and test for leaks before the burner is ever lit.
  • Electric tanks draw on a dedicated circuit, usually 240 volts, so the breaker and wire gauge have to match the new unit.
  • Converting from electric to gas means cutting into the wall or slab to run a gas line to where the tank sits now.

An electric tank is the simpler machine. One or two elements sit down in the water itself, and the thermostat cycles them on and off to hold the temperature you set. There's no flame, no flue, no combustion air to worry about. A gas tank works differently. A burner sits underneath the tank and heats the water from below, with a flue running up through the middle to carry exhaust out of the house. That flue has to be sized and vented correctly, either through a draft hood that relies on natural draft or a power vent with a fan, and an electric tank has no equivalent to either one.

This is where installation gets more involved on the gas side. Before a burner is ever lit, the gas line feeding it has to be sized for the tank's input rating and pressure-tested for leaks. If you're converting from electric, that often means cutting into a wall or slab to route a new gas line to where the tank sits, not just swapping one tank for another in the same spot. Electric installation has its own requirements too. Most tanks run on a dedicated 240-volt circuit, and the breaker and wire gauge have to match what the new unit calls for, which isn't always what the old one needed. Either way, this is plumbing, gas, and electrical work together, not a job suited to guesswork.

A middle-aged woman with shoulder-length dark hair, wearing a gray cardigan over a cream top, sits in an upholstered armchair and looks toward a sunlit window, with a shelf holding framed pictures and a plant behind her.
A woman and a child wrapped together in a knitted gray blanket on a couch, with the child's head resting on her shoulder and a lit table lamp and houseplant in the background.
A gray cylindrical water heater with two access panels stands on concrete blocks beside a brick wall in a basement, with copper and metal pipes above and shelving visible in the background.

The right pro for this job

One installer gets your project, so there's no bidding war over it.

A local installer who puts in water heaters gets your project.

Reach a local pro

Sending the form costs nothing.

Staying Electric Or Switching To Gas

Staying Electric

  • Installation means disconnecting the old tank and setting a new one on the same wiring and water lines, no new permits for gas.
  • A licensed installer still needs to check your breaker size and wire condition, since tank sizes and element wattages vary.
  • There's no flue to route and no gas line to pressure test, so the job usually stays contained to the space the tank already sits in.
  • If the tank is in a closet or garage, an installer can confirm the electrical panel has the capacity before swapping anything out.
  • Power here runs at a typical price, so staying electric doesn't carry a cost penalty the way it might somewhere with higher rates.
  • Any local code requirements around seismic strapping or drain pans still apply, and an installer will know what your city requires.

Switching To Gas

  • A new gas line has to be run from your home's existing gas supply to wherever the tank sits, which an installer sizes and pressure tests.
  • Venting needs a clear path to the outside, and an installer has to figure out that route before the tank goes in.
  • Local permits and inspection are required any time a new gas line goes in, and a licensed installer handles that process.
  • If your home doesn't currently have gas service, switching means coordinating with the gas utility before installation can even start.
  • The installer needs to confirm clearance around the tank for combustion air, since a gas unit draws air differently than an electric one.
  • Getting the vent height and termination point right matters for safety, and that's a detail worth having a qualified installer handle rather than guessing.
A gray-haired man in a dark sweater sits on a light gray sofa in a living room, looking toward a sunlit window with trees outside.
A gray-haired man in a dark blue sweater sits on a light gray sofa in a sunlit living room, looking off to the side, with a potted plant, shelving unit, and large glass doors behind him.
A bearded man with graying hair in a dark green sweater sits on a sofa in a living room, looking off to the side, with a sliding glass door and a dim kitchen doorway behind him.
A gray-haired man in a dark knit sweater sits on a light gray sofa in a living room, looking toward a sunlit window, with houseplants, a lamp, and framed art in the background.

59.9% of homes statewide heat with electricity

If your water heater runs on electric, you're in the majority here, and the wiring and breaker it needs are already common work for installers across the state. Staying electric means your replacement is routine, not a special case.

ACS 2020-2024 5-year B25040

  1. An installer sizes the new tank to your household's hot water use.

  2. The old water heater gets drained and disconnected from its lines.

  3. The new tank is set in place and connected to power or gas.

  4. The installer checks the pressure relief valve and fills the tank.

A smiling man in a denim shirt and white t-shirt stands in an open dark doorway of a stucco house, facing a woman with long brown hair and a green jacket seen from behind in the foreground.

Electric still works fine here

Most Arizona homes do fine staying electric, and if you're adding gas, that's a bigger job with a gas line and venting to get right. Either way, the installer you end up with needs to size the tank correctly, check your wiring or gas line condition, and set the pressure relief valve the way it's supposed to be set.

A local installer who handles water heaters all year has seen what usually goes wrong in homes like yours, whether that's an undersized breaker on an older electric tank or a vent run that needs rework on a gas install. You'll be matched with one licensed installer for your situation, not a handful of companies competing for the job, and that installer will reach out to you directly once you request it.

Interior corner of a room with a window and sheer curtain at left, a gray upholstered sofa with a cushion at right, and a round wooden table holding stacked books and a round vase with an olive branch.
A single-story stucco house at dusk with a lit paver walkway lined by low path lights, desert plants and boulders in front, and distant mountains under an orange and blue sky.

Water Heater Installation

Matched to your water heater job

Step 1 of 3: Equipment
  • A beige upholstered armchair with an olive cushion sits in a sunlit corner beside a wooden side table holding a ceramic vase with leafy branches, under a framed abstract artwork, on a woven rug over a wood floor.
    • Say what's going on with your water heater, and a pro who works on them reaches out.
    • A local pro who knows water heaters gets your details and gets in touch.
  • A gray outdoor condenser unit on a concrete pad surrounded by dark gravel, beside a dark wood-sided wall with an electrical disconnect box and a stone veneer wall with a small evergreen shrub.
    • Send the form and stop researching installers for the new water heater.
    • One request ends the search for a water heater installer.
  • A beige upholstered oversized armchair with a matching cushion and a knit throw draped over one arm, beside a round wooden side table holding a vase of greenery near a curtained window, with a framed landscape print on the wall and a woven rug on a wood floor.
    • Skip collecting and comparing quotes for the new water heater.
    • Skip the round of in-home estimates for a new water heater.
  • Sunlit living room corner with a beige upholstered sofa, cushion and knitted throw, a round wooden side table holding a white ceramic vase of leafy branches and a small wooden bowl, a framed landscape painting on the wall, and a window at right.
    • The pro who reaches out is licensed in Arizona.
    • Only one pro gets your request, so you hear from one company.